FX Series

Hammer Hydraulic Breakers

15 models for excavators with operating weight from 8 to 200 ton

Tubes with swivels

tubes with swivels fully protected

Hydraulic greasing

automatic hydraulic greasing device

Operating pressure

adjusting of the operating pressure

Adjustment of blows

manual adjustment of blows

Anti-dust

anti-dust and underwater work set up, for tunnels

Blank firings

hydraulic system for blank firings

Horizontal Tabs

The breakers of the FX series, thanks to their power and efficiency and to the right ratio between weight and power, are suitable for secondary demolition work, excavations in quarry, work in urban areas, tunnels, pipelines and railway tunnels and, concerning the biggest models, demolitions in open pit mining.

15 models for excavators with operating weight from 8 to 200 ton

  1. Tubes with swivels fully protected from any bad uses and resistant to vibrations in case of lack of nitrogen in the chamber.
  2. Regulation of the operating pressure For the FX series (FX950-15000), it is possible to adjust the working pressure by a manual valve located frontally, on the distribution of the breaker.
  3. Anti-dust and underwater work set up You can prevent the entry of dust and water into the breaker by blowing air into the proper hole in the front part of the breaker, with a pressure not less than 10 bar.
  4. Automatic hydraulic greasing device (optional, mounted on the breaker) The Beka-Lube automatic lubrication system optimizes the lubrication procedure and reduces maintenance and downtimes.
  5. Automatic hydraulic greasing device with exclusive Hammer electric control (optional, mounted on the excavator). Innovative electric system with automatic grease distribution, less liable to vibration breakages thanks to its own tank of grease with a capacity of 4 kg or 8 kg, making thus the system cheaper than all the other devices with single cartridges.
  6. Manual adjustment of blows For the FX series (FX950-FX15000), the regulation of the blows is carried out manually by an adjusting valve located on the side of the breaker.
  7. Hydraulic system for blank firing the hydraulic system is a regenerative circuit of oil that avoids blank firings when the tool is not in contact with the rock.
  8. The piston is built with a special geometry such as to keep a constant energy of impact, as well as for reducing breakages in conditions of criticality.
  9. Anti-dust system for tunnels (optional) The anti-dust system consists of the addition of a dustproof seal mounted in the lower bush so to avoid the entering of impurities in the circuit.
MODELLIFX700FX950FX1300FX1700FX 1900FX2200FX2800FX3200FX3700FX4200FX5000FX6000FX8000FX12000FX15000
Peso escavatore (t)8-1210-1614-1918-2422-2723-3128-3830-4035-4035-4540-6545-7560-11080-170100-200
Peso (Kg)700950120016501850220029003200370044004850580078001200014500
Altezza del corpo (a) (mm)131013901470167017901840203020302250225023902390184020302030
Altezza dell’utensile (b) (mm)430550560620725720710710790790700620720710710
Diametro dell’utensile (mm)95115120135140150160160180180195195215255280
Portata olio rich. (l/min)70-10090-120110-140130-160140-180165-190180-240200-260250-300270-320290-350300-380380-440480-570500-600
Pressione di esercizio (bar)160165170180180180180180180190190190190190190
Numero dei colpi (/min)600-900600-900400-900400-800400-800400-800350-700300-650300-650300-650250-550250-550200-400150-300150-250
Energia del colpo (j)200026003200420047005400850090009500125001650018500230002800035000
Contropressione max. (bar)252525252525252525253030303030
Diametro tubo entrata (inch)3/4"1"1"1"1"1"1" 1/41" 1/41" 1/41" 1/41" 1/41" 1/41" 1/41" 1/21" 1/2
Diametro tubo uscita (inch)3/4"1"1"1"1"1" 1/41" 1/41" 1/41" 1/41" 1/41" 1/41" 1/41" 1/41" 1/21" 1/2
*All illustrations and numerical data in this catalog are purely indicative and subject to change at our discretion and without notice. We therefore reserve the right to modify them with a view to improving and constantly developing our produc.

Moil Point

Suitable for concrete, medium-hard and not layered rocks.

Blunt Tool

Suitable for reinforced concrete and very compact rocks.

Pyramid Tool

Suitable for reinforced concrete and very compact rocks.

Cobra Tool

Suitable for quarry works, such as primary demolition and reduction of stone blocks.

Chisel Tool

Suitable for medium-hard and layered rocks.

Hydraulic greasing

The Beka-Lube automatic lubrication system optimizes the lubrication procedure and reduces maintenance and downtimes (optional)

Request info





    Energistically benchmark focused growth strategies via superior supply chains. Compellingly reintermediate mission-critical potentialities whereas cross functional scenarios. Phosfluorescently re-engineer distributed processes without standardized supply chains. Quickly initiate efficient initiatives without wireless web services. Interactively underwhelm turnkey initiatives before high-payoff relationships. Holisticly restore superior interfaces before flexible technology. Completely scale extensible relationships through empowered web-readiness. Enthusiastically actualize multifunctional sources vis-a-vis superior e-services.

    Interactively underwhelm turnkey initiatives before high-payoff relationships. Holisticly restore superior interfaces before flexible technology. Completely scale extensible relationships through empowered web-readiness. Enthusiastically actualize multifunctional sources vis-a-vis superior e-services.

    Images


    Contattaci

    Richiedi informazioni sui prodotti

    Lorem ipsum dolor sit amet, consectetur adipiscing elit. Aenean ac tempor neque, id pretium ligula.